how loud is a 22 rifle

A Boom Or A Whisper? | How Loud Is a .22 Rifle?

Shooting firearms recreationally can be an enjoyable hobby, but it can also come at a price to your hearing.

Firearm noises can be especially harmful as they have high and low frequencies that can damage your hearing, mainly when the frequencies are sustained at increased volumes.

Exposure to loud sounds over a long period may result in permanent hearing damage. This is why wearing ear protection is essential when shooting any gun type.

How Loud Is A .22 Rifle

But, let’s zero in and discuss one popular gun in particular… the .22 rifle.

The .22 rifle is often used for hunting small game and is common among recreational shooters. .22 caliber firearms produce noise levels ranging from 120 to 140 dB (decibels), meaning they’re louder than everyday conversations, which emit about 60 decibels of sound.

Is a .22 rifle louder than a shotgun?

.22 rifles aren’t as loud as shotguns. A shotgun can go up to 160 decibels, while a .22 rifle goes to around 130-140 decibels.

man shooting shotgun

A shotgun is louder than a .22 rifle, as the air blast it releases is greater when the gun is fired.



How loud is a 9mm vs. a .22?

A .22 caliber bullet is quieter than a 9mm, the most common firearm round.

While a .22 emits about 120 sound decibels, a 9mm produces up to 160 because a .22 has smaller rounds than a 9mm. As a result, the kinetic energy it possesses when fired isn’t as much, resulting in less noise.

9mm bullets

9mm rounds are louder than a .22 rifle, due to their size.

A .22 rifle is an excellent option for those looking for relatively quiet but powerful guns. It’s ideal for small game hunting and target shooting and won’t bother your neighbors as other bigger calibers might.

Although .22 rifles are quieter than other guns, it’s still vital to take measures to protect your ears when shooting one.

Using hearing protection can shield you from the high-pitched noise they produce as it may potentially damage your ears.




How far can you hear a .22?

How far you can hear a .22 varies depending on how sound travels and the environment.

Under perfect conditions, you can hear it from up to two miles away. Nevertheless, in an urban setting with many noise sources and buildings, the distance can be reduced to a few hundred yards.

A classic .22 caliber round emits sound that is comparable, in decibels, to a an ambulance siren or a rock concert.

A .17 HMR cartridge is a quieter option that produces around 100 decibels of noise.




How loud are .22 subsonic sounds?

The decibel scale measures sound intensity. And while a a .22 caliber round is considered a low-intensity round, the decibel level can vary based on the ammunition and gun types being used.

For instance, a suppressed .22 pistol could have around a 95 dB noise level, while the unsuppressed one could go up to 135 decibels.

.22 subsonic round

If you want a quieter round that won’t bother your neighbors, a .22 caliber subsonic round can be the way to go. These rounds move at speed lower than a standard round, significantly reducing noise levels.




How to Protect Your Hearing From Firearm Noise

While you may love hunting, enjoying it without hurting your hearing should be a main focus.

People who use firearms are at a greater risk of experiencing tinnitus, hearing loss, and other hearing problems.

Exposure to more than 85 decibels may result in noise-induced hearing loss. The loud sound can permanently destroy the hairs in your ears that stimulate the auditory nerve fibers.


GLORYFIRE Shooting Ear Protection Earmuffs, Bluetooth Hearing Protection Ear Muffs for Noise Reduction
$219.99
Buy Now
We earn a commission if you make a purchase, at no additional cost to you.
03/06/2024 08:05 pm GMT


Other factors contributing to harmful noise levels when using a firearm may include gun modification mechanisms like muzzle breaks or discharging the firearm where sounds can echo or reverberate.

Hearing loss also impacts how you hunt, and may be tied to cardiovascular disease, depression, cognitive decline, balance issues like falling, isolation, social withdrawal, and other challenges.

Good hearing promotes situational awareness, which is crucial in the field. Hearing protection ensures that attention is present when you need it the most.

Understanding hearing protection and hearing enhancement will help you better protect your ears. Outlined below are ways to protect your hearing from firearm noise.




Use earmuffs

Earmuffs are personal protective gear meant to protect you against excess noise pollution. They’re made of sponge and thermoplastics and have a pair of cups. The cups are usually attached to a steel or plastic headband’s outer ends to fit over your ears’ top while covering them tightly.

You can wear acoustic earmuffs alone or with earplugs, reducing dangerous noise that can potentially damage your hearing.




Try earplugs

Earplugs come in various types, and this is why you should consult a professional to identify a proper hearing protection solution. Some may include:

  • Custom earplugs: They contain special filters for an accurate, even noise reduction level. You can have custom earplugs programmed to lessen sounds by the necessary amount and filter specific sound types more than others. They’re made with molds of your ear by a skilled professional, ensuring they’re a perfect fit and seal your ear better than standard earplugs. They’re comfortable and ideal for wearing for longer hours  
  • Electronic shooter earplugs: Electronic earplugs can listen to the noises around you, offer automatic protection from impact noises like gunshots, or gradually turn up a reduced protection noise reduction rating in response to background sounds slowly increasing to hazardous levels. They offer you the protection you require from one moment to another without removing or fiddling with your earplugs. Electronic earplugs can let lower decibel sounds pass while blocking harmful noises.
  • Reusable shooter earplugs: They’re an effective way to reduce sound levels, protecting from high shooting decibels. When looking for reusable shooter earplugs, note that various reusable earplugs have different noise reduction ratings. The higher the ratings, the better the noise reduction level provided it’s a good fit for your ear. Reusable shooter earplugs are durable and can be used multiple times

#ad



Endnote

While a .22 is not as loud as many other rifles, it can still be pretty loud, impacting your hearing. So, consider using hearing protection each time you use any gun, to prevent permanent hearing loss and other impairments.

Safe and happy shooting!

crimson talon broadheads header image

Crimson Talon Broadheads (Fixed Blade) | The Inside Information

In this review, I tested three models of the Crimson Talon fixed-blade broadheads.

Crimson Talon makes the G2, the G2 Hyperspeed and the Outlaw.

crimson talon broadheads

The Crimson Talon lineup features the G2, the G2 Hyperspeed and the Outlaw.

The G2 Broadhead Specs

First we have the G2. It has a camouflage ferrule that they refer to as “ferruleflage.”

What initially stands out about the G2 is that it has six total blades – three main blades and three bleeders.

The main blade’s diameter is 1.25 inches, which is a big cutting diameter for a 3-blade head.

crimson talon g2 broadhead blades

The G2 broadhead has curved blades as well as a camo ferrule they call “ferruleflage.”

The cutting diameter of the smaller bleeder blades is 1/2 an inch. So, although they are shorter, they help with the cut.

The total cut of this head is 2.6 inches!

The bleeders are also offset at a 60-degree angle, so that allows them to create an even better wound channel and do damage that is difficult to close up.


#ad

Crimson Talon Broadheads G2-100 Grain (3 Pack)
Buy Now
We earn a commission if you make a purchase, at no additional cost to you.

But the biggest differentiating factor on the G2 broadhead is that the main blades are curved. This apparently creates two advantages…

The other advantage of the curved blades is that once they hit the animal, they continue to rotate, causing a spiral wound channel. Combine that with the 1.25 inches of cutting diameter and 2.6 inches of blade cutting, and that creates a wound channel that is very difficult to close up.

Crimson Talon calls this curved blade feature their “spintite” airfoil technology. As the arrow flies, the curved blades function as vanes or fletchings would, creating quick rotation of the shaft, which results in more accurate flight. This is supposed to prevent arrow planing.

The tip is made out of A2 tool steel, so a really tough, beefy chisel tip of a very high quality steel. The ferrule is 7075 aluminum, which is a very stout, durable aluminum, stronger than some steels.

The blades of the G2 broadhead are 420 G2 stainless steel. The main blades were 0.028 inches thick, which is relatively thick compared to some other blades. But, with so much blade cutting action going on, that probably isn’t going to be an issue.



We’ll see how it does in the durability test below.

One of the cool things about all of the Crimson Talon broadheads is that they have 100% lifetime warranty for any breakage, for any reason, with no expiration and no limitations. So, if any of these heads break, you just send them in and you get a replacement. That’s pretty nice especially at the price point that they are sold at.



G2 Hyper Speed Specs

The next broadhead I tested was the G2 Hyperspeed. It’s the same head as the G2, but without the airfoil design. So, the blades are all straight.

hyperspeed broadhead blades

The Hyperspeed broadhead is like the G2, but without the curved blades.

Now, the bleeders are still offset at a 60-degree angle, but everything is just a straight blade. Some people that don’t want the airfoil designs will like this head.

I remember when I lived in Colorado, the Crimson Talons were illegal (at least at that time) because the blades had to exist in a continual single plane. They couldn’t be curved.

Crimson Talon Broadheads Hyper Speed - 100 Grain (3 Pack)
$26.95
Buy Now
We earn a commission if you make a purchase, at no additional cost to you.
03/06/2024 02:11 pm GMT

The Outlaw Specs

The last Crimson Talon head I tested was The Outlaw.

The Outlaw is it’s really basic in some ways and unique in others. It’s basic in the sense that it’s a 3-blade head with a 1-1/8 inch cut. It’s a little bit different in that all three blades are offset. The 0.040 inch thick, stainless steel blades are an offset design, to create a better wound channel.

offset blades of outlaw broadheads

The Outlaw broadhead has offset blades and a 1-1/8″ cut.

The tip is hard stainless steel and the ferrule is solid titanium. It also has a 3-blade locking system, keeping the blades in three different places, which is supposed to make these heads very durable and have really good blade retention.


Crimson Talon Outlaw 100-Grain (3 Pack)
Buy Now
We earn a commission if you make a purchase, at no additional cost to you.

Crimson Talon Broadhead Testing

I was eager to put all of these heads to the test.

I tested them for flight, edge retention, sharpness, penetration and durability.

Let’s see how this Crimson Talon lineup performed.




Crimson Talon Flight

All three of the Crimson Talon heads were able to pop a balloon at 70 yards.

Edge retention results (out-of-the-box sharpness)

For the Crimson Talon G2, I just tested the sharpness and edge retention of the straight blades (Hyperspeed), because it’s too difficult to get it all lined up with the curved blades and they are the same blades anyway.

stroking arrow on g2 broadheads shaft

The Crimson Talon G2 Hyperspeed cut paper after 5 strokes of the arrow.



stroking an arrow shaft on outlaw broadhead

The Outlaw cut paper after five strokes of the arrow.

Penetration results (ballistic gel)

penetration of crimson talong broadheads in ballistic gel

The penetration of these heads was pretty much as expected. The Outlaw penetrated the most at 8 and a half inches, followed by the Hyperspeed at 7 and a quarter inches. And then the G2 with the curved blades penetrated 6 and 3 quarter inches.



g2 broadheads into ballistic gel

Down at the bottom there in the middle, you can see the wound channel of the G2 and you can see that rotation. The blades actually rotated from initial impact with the rubber foam mat to their final resting place. They rotated 90 degrees. So that’s pretty cool. That’s like a single bevel, 2-blade head in terms of rotation. And, that’s a wicked-looking wound channel as well.



crimson talon broadhead holes in steel plate

Here are all three heads after going through the 22-inch steel plate five times each. I was definitely impressed with the durability. I really didn’t expect any of them to make it through all five times. I expected them to lose blades on maybe the second or third shot. But, none of them did. All of them held their blades together really well and stayed intact.



Penetration (steel plate)

If you look at the holes that the heads made in the steel plate, it’s really interesting. You can see that the Hyperspeed (top right) made the most impressive holes. It made really big, triangular holes with extra wide cuts in the tips.

g2 broadhead damaged blades

Notice the G2 with the curved blades. I’m really surprised that it held together like it did. The blades did not straighten out when going through the steel plate five times. They really stayed curved together, which is really impressive. Also, the holes are still really big. You can see the curls in the ends. It didn’t make as big of a triangular hole as the Hyperspeed for some reason, but it still made a really impressive wound channel with those “S-cuts.”



outlaw after going through steel plate

The Outlaw held together as well. And you can see the holes are a bit smaller there, that at a 1 1/8 inch cut.

Edge Retention (steel plate)

Now, in terms of the edge retention and the durability of the blades themselves after going through the steel plate; again, all of them stayed intact. None of them bent out of shape. But, all of them did get really nicked up.



The one that probably got the most nicked up was the G2. Because of those curved blades, the head hits the steel in a new place each time as it curves around. And so, those edges would have had to be replaced after probably the third or fourth shot. But they still held intact. You can imagine there might be some damage when coming in contact with a rib, shoulder or other bones of a deer.


#ad



The Outlaw has the thickest blade, so they took a big brunt of the impact on the steel and they got next most nicked up (although the tip held together perfectly and the A2 tip on the G2 and on the Hyperspeed look brand new).

The Hyperspeed got the least amount of damage on the blades. It made it through four times before it would have had to be replaced. So, it stayed in relatively good shape. Some of the blades were still perfectly intact and some were nicked up.

So overall, really impressed and surprised with the durability of these heads.



Crimson Talon broadheads: Final thoughts

So what do you think of the Crimson Talons? I’ve got to say, I was really impressed.

When I first saw the price point looked at the heads, I thought, “Man, these things are going to fall apart.” I just thought they were kind of cheap.

But man, I was wrong! They really did perform in each one of the tests that I did on them. I was pleasantly surprised.



So, you can check out the score sheets below and see how they rank compared to each other and compared to other heads.

After reviewing these heads, if I had to pick a winner between them, it would definitely be between the G2 and the G2 Hyperspeed. And which one would be the winner would be based on my setup and on what animal I’m pursuing.

g2 broadhead score card
hyperspeed broadhead score card
outlaw broadhead score card


If I’m going after a really big animal or I have a lighter setup where I need to maximize penetration, then I’m going with the Hyperspeed.

If I’m using a setup that has a little bit more momentum, and I’m going after an animal like a whitetail sized animal, I’m going with the G2 because that is one wicked-looking wound channel!

But these two heads are fantastic heads. If I decide to pick one for my setup then it would be the G2. But, I’d be a 100% confident using both of them on an animal.

Great job, Crimson Talon. Give these a look. 

gravedigger hybrid broadhead

Gravedigger Broadheads Review | The Inside Information

In this review, I’m going to be covering a broadhead that has been around for a while. It’s one I’ve actually used in the field quite a bit and been fairly successful with. It’s called the Gravedigger.

The Gravedigger Hybrid broadhead overview

Let’s take a look at the design and some of the features of the Gravedigger Hybrid head (it’s called a “hybrid” because it has both fixed and mechanical blades). Then, I’ll show you how it performed when I put it through my standard array of tests.

gravedigger hybrid broadhead in closed position

Here is the Gravedigger hybrid in the closed position.

gravedigger hybrid broadhead chisel tip

This Gravedigger hybrid model has the chisel tip. (They also make a cut on contact tip where the fixed blades extend all the way up to the top).

The cutting diameter of the Gravedigger Hybrid’s fixed blades is 1 inch. In the closed position, the mechanical blades are ½-inch. So, just in the closed position, if the blades were not to open at all, it would be an inch and 1/2 of a cut, which is no slouch of a cut.

But the mechanical blades do open. They open really well, in fact. They’re not held in place by an O-ring or a retention clip, but rather just by friction, and that’s adjustable with a small Allen bolt.

The cutting diameter in the open position here is a full 1 and 3/4 inches. So, 1 and 3/4″ by 1″ – that’s a lot of cut!

adjustable friction screw on gravedigger broadhead

You can adjust the tension that holds the blades in place. But, when they encounter a medium, they open over the top and they fall back into their fully opened position.


BLOODSPORT Gravedigger Extreme 4-Blade Hunting Hybrid Mechanical Broadhead with Chisel Tip - 100 Grains | 2.25" Cutting Diameter | 3 Pack
$39.99
Buy Now
We earn a commission if you make a purchase, at no additional cost to you.
03/07/2024 05:05 pm GMT


Gravedigger Blade specs

The blades of the Gravedigger are made out of a 416 stainless steel. The ferrule is a 7075 aluminum. It’s a pretty vented blade, but it’s still is a good stout aluminum, and the tip is a hardened steel, really stout, chisel tip.

I couldn’t find any information listing the blade thickness, so I used my micrometer to measure. The fixed blade measured 0.039 inches thick and the mechanical blades were 0.032 inches thick.

Gravedigger broadheads testing

I was eager to see how this head performed in my tests. I did not test it for long range flight, because I know it flies really well.

I consider it like a mechanical in terms of flight in the closed position, and I don’t test mechanicals for long range flight, because they all fly really well, even though this head has the little one inch fixed blade. I know it flies fantastic.

I tested for edge sharpness and retention, for penetration, and for durability.

Let’s see how the Gravedigger performed.


#ad

Pine Ridge Archery The Arrow Inspector, Black
$29.99
Buy Now
We earn a commission if you make a purchase, at no additional cost to you.
03/06/2024 08:50 pm GMT


Sharpness Test

The Gravedigger cut paper after four strokes of the arrow.

carbon arrow shaft dulling the gravedigger hybrid

I use strokes of carbon shaft arrow to dull the blades. I want to see if they can still cut paper after each stroke.

gravedigger broadhead paper cut test

I use strokes of carbon shaft arrow to dull the blades. I want to see if they can still cut paper after each stroke.



Ballistic Gel Penetration Test

The Gravedigger penetrated 6 and 1/4 inches through the foam and ballistic gel.

gravedigger ballistic gel penetration

The Gravedigger penetrated 6-1/4″ into the ballistic gel.



entry hole of gravedigger broadhead in ballistic gel test

Here’s the entrance of the Gravedigger. And you can see that the mechanical blades opened almost 1-3/4″ on impact. That bottom blade for whatever reason deployed a bit more effectively than the top blade. But, both of them opened up quite well for an over the top mechanical.





MDF penetration test

I shot the Gravedigger through MDF five times. Below are the pictures.

I shot the first one in the closed position and the baldes didn’t open very much. But, then on the following shots, I kept the head in the open position when I was shooting, just to test durability.

gravedigger hybrid after going through MDF

Here, you can see the Gravedigger after going through a half inch MDF five times. As you can see, it held up relatively well. The tip is in still in great shape. The ferrule is also in great shape. The fixed blades are in perfect shape. And the mechanical blades also did really well. They didn’t break off.



bent blades on gravedigger broadhead after going through mdf

Now, in terms of a bend, they did bend backwards a bit. The original on the left gives you a frame of reference. After the shots, there is quite a bit of arch to the expandable blades. But you know what? If you’re going to have a problem with the head kind of “failing,” that’s the way to do it. It’s not really a fail, because it’s continuing to cut even after going through this MDF five times. So, if there’s going to be any kind of a problem, to bend in that direction is the way to go. So overall, very impressive.





Final Thoughts

So, what do you think of the Gravedigger?

Going through these tests reminded me why I liked it so much when I first started using it way back.

There are just so many heads. It’s hard to keep using just one. I’m a broadhead junkie and like to keep trying new things!

But, this is definitely a broadhead that’s worth a look. There are some weaknesses to it but there are a lot of strengths to it as well. It performed fairly well for an over-the-top mechanical.

So, check out the score sheet below and see what you think about it, and decide if these broadheads are the right heads for you.

gravedigger hybrid scorecard
Gravedigger Hybrid score card.