blood therapy ocd broadheads

Blood Therapy Broadheads Review | Gimmick or the “Wheel Deal?”

Talk about a unique broadhead.

Honestly, I never would have been interested in testing the OCD Blood Therapy broadheads, but when a viewer of my channel sent it to me, I thought, “Oh, this is going to be fun.”

The “OCD” in the name stands for “Ours Cuts Deeper.”

We will see about that.

This head as a wheel-shaped, circular design. I’ve tested countless broadheads and I’ve never seen anything like it.

So, I wanted to see… is it a gimmick or is it the real deal?

OCD Blood Therapy broadheads up close

Before I get to the test results, let’s take a look at the OCD up close.

blood therapy ocd broadhead up close

Here, you get a nice good look at the OCD. And you can see, this is really a unique innovative head.


leading blade of blood therapy ocd broadhead

It also has a main leading blade to serve as a crosscut. This head definitely look innovative.


wheel turning on ocd blood therapy broadhead

The circular design of the OCD may seem a bit gimmicky, but the theory makes sense… When you hit a hard bone, it will rotate. The blade does in fact rotate somewhat, so it could potentially rotate around really tough parts of a deer’s anatomy, or other animal.




Blade specs

The circular blade has a 1-inch cutting diameter. The leading blade has 9/16-inch cut. So, the total cut is 1-9/16 inches. So, not huge, but not bad either. It’s a little under 1.6 inches of total cut.

The ferrule of the OCD is made out of 7075 aluminum which, if you’re going to use aluminum, is a really good one to use. That’s stronger than some steels.

The blades are pretty impressive as well. They are made out of 420J2 stainless steel and they are really thick. The circular blade is 0.059 inch thick. It’s a double bevel. And that leading blade is 0.039 inch thick.

So, really good materials and a really interesting design.


Blood Therapy OCD Broadheads (3-Pack), 100-Grain, Red
Buy Now
We earn a commission if you make a purchase, at no additional cost to you.

As always, I performed this test using my Bowtech SR6 set at 72 pounds, on the comfort setting, with a 27-inch draw. I used Bishop FOC King Arrows, 460 grains. Let’s see how the Blood Therapy OCD performed!

Testing of the Blood Therapy OCD heads

I was eager to put it to the test and see how it goes. I tested the OCD for long distance flight, edge sharpness and retention, for penetration, and for durability.

Long-Range Flight

The OCD flew very well, as I was able to pop a balloon from 70 yards away.

Out-of-the-box sharpness test

In this test, I ran a carbon arrow shaft over the blade (up to five times) to see how many strokes of the arrow the blade could handle and still cut paper.

The Blood Therapy cut paper (barely) after five strokes of the arrow.



strokes of the arrow shaft on a blood therapy broadhead

For out-of-the-box sharpness testing, I ran a carbon arrow shaft over the blade to see how many strokes of the arrow the blade could handle and still be able to cut paper.


cutting paper with blades of ocd broadhead

The OCD could cut paper (just barely) after the 5th stroke of the arrow shaft.




Penetration testing

I shot the OCD into ballistic gel that was fronted with a foam rubber mat and 1/2″ MDF.

The OCD penetrated 9-3/4 inches. Very good penetration for sure.

ocd broadheads penetrating ballistic gel

The OCD penetrated 9-3/4 inches… fantastic penetration!



GhostBlind 4-Panel Predator Blind, Silver
$231.86
Buy Now
We earn a commission if you make a purchase, at no additional cost to you.
02/05/2025 03:49 am GMT

Durability testing (Steel plate test)

In this durability test, I shoot a broadhead into a 22-gauge steel plate to see how it holds up (will shoot up to five times.)

Now, the head did fantastic through three shots. But on the fourth shot, the pen that holds the rotating circular blade in place broke off. The leading blade, however, was in pristine condition. Amazing! It doesn’t even look like it has hit anything. And yet, it cut through the steel plate four times.

The rotating blade did really well also. It got a little bent out of shape, but it did relatively well and much better than I thought it would do. It made it through three times perfectly and then broke on the fourth time.

ocd broadhead after shot through steel plate

Here’s the OCD after being shot into the 22-gauge steel plate four times. You can see it made four nice holes. They are relatively small due to its small cutting diameter. It still made a decent wound channel.



OCD Broadheads | Final Thoughts

OK. So what do you think of the OCD?

When I first heard about this, I thought it was 100% gimmick. Every time I had seen a picture of it, I said to myself, “Man, what a crazy, stupid design!”

I was wrong.

They call it OCD (Ours Cuts Deeper) for a reason, and it really did cut deeper!

This head penetrated extremely well in my tests. I was surprised.

And then, I didn’t think it was going to fly well. And, as you saw, it flew really well.




I didn’t think it was going to hold together through a steel plate, but it held together pretty well.

So, this is a head that’s really interesting. It’s beyond just being a novelty. There’s really some good stuff to it.

Now, the overall cut is relatively small. An inch one way, and 9/16 of an inch the other way, so it’s pretty small cut. That’s one of the reasons it flew so well and penetrated so deeply.

So, check out the score sheet below and see what you think of the Blood Therapy OCD broadheads!



blood therapy ocd broadheads score card
Here is the testing score card for the Blood Therapy OCD broadheads.
innerloc carnage broadhead

Innerloc Carnage Mechanical Broadheads | Greatness or Gimmick?

I have to hand it to Innerloc Broadheads. The Carnage mechanical head definitely a cool and innovative-looking head.

I had been wanting to test these for awhile to see if the innovation translated to stellar performance.

So, let’s take a closer look at these heads.

As always, in this testing, I used my Bowtech SR6 set at 72 pounds, 27-inch draw, and a 460-grain Bishop FOC King Arrow.

Innerloc Carnage Broadheads Up Close

Now, the interesting thing about these heads is the way the blades stay together in the closed position. They don’t use an O-ring (i.e. the Afflictor Hybrids). They don’t use a retention clip. So, how do they keep the blades closed until deployment?

They use a sticker.

What?

That’s right. A sticker.

I have to say, it’s creative and different. Not only that, but they have a variety of stickers to choose from. They even have a program on their website where you can design and personalize your own sticker.

innerloc carnage broadheads and sticker
The Innerloc Carnage expandable broadheads use stickers to hold the blades closed.

When it’s in the closed position, the Carnage has nothing exposed. That’s going to fly extremely well. I don’t test mechanical heads for flight because they all fly really well. But for this, I imagine it’s going to fly extremely well. I’d say that’s probably going to be its greatest super power is its flight, in addition to its cut size.

innerloc carnage expandable broadhead with sticker applied
If you’re feeling really patriotic then you can go with this one. And what you do is you just wrap it around the blades. I will say, it’s not super easy, but it’s not rocket science either. Now, you’re ready for the 4th of July.




innerloc carnage in fully open position
Here, we get a good look at the Carnage in a fully open position. The cutting diameter is 1-½ inches, which makes a really nice cut for a 3-blade head. The blades themselves are 0.040 inch thick, so they are thicker than most mechanical blades.
cutting diameter of carnage broadhead
The Carnage has a 1-1/2″ cutting diameter, which is very good.
innerloc carnage in closed position
In the closed position, the blades tuck under like this. Then, with pressure on the tip, the blades are forced back.
innerloc carnage rear deploying
You can see how the blades come out from the back. And so, I would imagine they’re going to fully open upon impact, and you’re going to get that full 1-1/2″of cutting diameter. It’s going to stay that way all the way through, as long as there’s pressure on this little plunger tip.

Now, its durability and its penetration, I wasn’t really sure about. So, I was eager to put this head to the test and see how it performs.

Innerloc Carnage 100 Grain Expandable Broadhead for Crossbows
$48.10
Buy Now
We earn a commission if you make a purchase, at no additional cost to you.
02/05/2025 05:38 am GMT


Edge Retention Testing

In the edge retention test I push paper down on the blades of the broadhead after every two strokes of the edge of an Easton Hexx Shaft. This tests how well the blade holds its edge.

easton hexx shaft arrow on blade of innerloc carnage
I ran the shaft of an Easton Hexx shaft across the blade for two strokes and then test. I will do process up to five times.
cutting paper on blades of innerloc carnage
The Carnage was still able to cut paper after 10 strokes of the arrow.

Penetration testing

For the penetration test, I shout the Carnage head into ballistic gel that was fronted with a rubber mat and 1/2″ MDF board.


Pine Ridge Archery The Arrow Inspector, Black
$30.76
Buy Now
We earn a commission if you make a purchase, at no additional cost to you.
02/05/2025 03:22 am GMT

Cardboard penetration test

In the cardboard penetration test, I shot the Carnage into layered cardboard to see how many layers it could penetrate.

innerloc carnage after cardboard penetration test
The Carnage penetrated through 40 layers. And I might add, you notice how the blades set way back so that point, it’s like a nail, actually is what penetrated through the last several layers. But it did penetrate through the 40th layer.


Ballistic gel test

innerloc carnage penetrating ballistic gel
The Carnage penetrated 7 inches.
rubber mat entrance hole of carnage broadhead
Here, you can see the entrance cut into the rubber mat that fronted the MDF and ballistic gel. Man, it did really well. Those blades perfectly opened and fully deployed upon impact. And you can also see the sticker that came apart there as it impacted.
innerloc carnage broadhead after going through ballistic gel and mdf
Upon further investigation, the Carnage broadhead after going through ballistic gel and mdf was missing one of the blades. It’s rare that a broadhead loses a blade just in this one layer of MDF, but that is exactly what happened. There are only two blades. And it’s not in the gel. You can see the gel only has two blades cut into it. I found it behind the rubber mat layer. It broke off at the pin that holds the blade in place.

Because the Carnage lost a blade, I never even got to where I tested it by shooting it into MDF (up to 5 times).




Final thoughts on the Innerloc Carnage

So, what do you think of the Innerloc Carnage?

I will say, I thought it was pretty gimmicky at first, but it definitely has some strengths, such as its super low profile in flight, which makes it forgiving, its large cut, and its easy-open rear deploying blades.

But, it also has some weaknesses.

I question how well it’s going to do on angled shots because it has such a wide flared tip without anything to really grab upon.



But, the biggest weakness is its durability. You saw what it did in the 1/2-inch of MDF when it lost a blade. I did the test again, just to be sure… this time it lost two blades. There’s just an inherent flaw in that pin that holds the blades together. It just seems to be breaking in some way.

So, I know a number of people have used these heads and hey, more power to you if you really like them.

But, I’ll tell you this, the Carnage is not going to make it in my quiver. But, check out the scores below and see what you think and see how it did in the areas that matter most to you.

Best of luck in your hunting adventures!



innerloc carnage testing scorecard
Here is the final score card for the Innerloc Carnage broadhead.


dirt nap drt broadheads review header image

Dirt Nap DRT Broadheads | Fabulous Fixed-Blade?

The Dirt Nap DRT broadhead just looks cool.

You can even get different colors.

But, how will it perform when I put it through my battery of tests for long-range flight, edge sharpness and edge retention, penetration, and durability? Well, let’s find out!

dirt nap drt broadhead
The Dirt Nap DRT broadhead.

I was eager to put the Dirt Nap DRT broadhead through all the tests that I do. So, let’s see how the Dirt Nap DRT performed!

The Dirt Nap DRT broadhead up close and personal

The DRT head has a cutting diameter of 1-3/16-inches in one direction, but it also has a 5/8-inch crosscut, which is going to cut a healthy amount of tissue. It should open up a decent wound channel.

The blades are 420J2 stainless steel 0.051 inch thick. They are not replaceable, but they are pretty thick.

The ferrule is made out of 7075 aluminum, which is a pretty stout aluminum. And this comes in 100 and/or 125-grain due to a removable washer that makes up the extra 25 grains.

If you keep the washer on, and you have a 125-grain head. Take it out, and you now have a 100-grain head. So, in a sense, it’s modular.



dirt nap drt broadhead cutting diameter
The DRT has a diameter in one direction of 1-3/16 inches.
dirt nap drt broadhead bleeders diameter
The cutting diameter of the bleeder blades is 5/8-of-an-inch.
dirt nap drt broadhead with 25 grain collar
The DRT has a 25-grain collar, that if kept on the head, makes it 125 total grains (if you’re looking for a heavier setup).


Leupold RX-2800 Rangefinder, TBR/W
$429.99
Buy Now
We earn a commission if you make a purchase, at no additional cost to you.
02/05/2025 04:58 am GMT

Long-range flight of the DRT

In my long-range flight accuracy test, I was able to shoot the DRT head and pop a balloon from 70 yards.




Out-of-the-box sharpness test

In the out-of-the-box sharpness test, I give the blades of the head I am testing a stroke from a carbon arrow shaft and then see if the blade can still cut paper (up to 5 strokes of the arrow).

a carbon arrow shaft going over the blade of a dirt nap drt broadhead
I run a carbon arrow shaft across the blades of the broadhead I am testing to see how the blades cut paper after being dulled in this manner.
dirt nap drt broadhead cutting paper while testing sharpness
The Dirt Nap cut paper after all 5 strokes of the arrow.



DRT penetration test

In my penetration test, I shot the DRT into a block of ballistic gel that was fronted with 1/2″ MDF board.

dirt nap drt broadhead penetrating nine inches through ballistic gel
The Dirt Nap penetrated 9 inches, almost as far as the Magnus Buzzcut.

Rinehart® 18-1 Broadhead Target
$166.58
Buy Now
We earn a commission if you make a purchase, at no additional cost to you.
02/05/2025 03:39 am GMT

Durability testing

In the durability test, I shot the DRT into a .22-gauge steel plate (up to five times) to test how well the head would hold up.

dirt nap drt broadhead after going through steel plate
Here’s the Dirt Nap after going through the steel plate five times. And, on the positive side, the blades didn’t really fold over or break or bent terribly or come out of the ferrule. It all stayed intact. On the negative side, the blades did get really dinged up, and that was after the third shot. I would have had to call it for score purposes that it would have to be replaced at that point because they’re beyond just being able to be filed out.

Overall, the DRT did relatively well. And the holes themselves, you can see that nice hole, better than a 2-blade would be because you get that crosscut in there as well.



Final thoughts on the Dirt Nap DRT heads

Performance really matters with broadheads. So, what do you think of the Dirt Nap DRT? It definitely performed better than what I was expecting.

You can compare the scores to other heads in similar categories.

But, I will say the Dirt Nap DRT broadhead is definitely worth checking out. I can see why a lot of people really like it.

dirt nap drt broadhead testing scorecard
Here is the scorecard for the DRT

Other fixed-blade reviews: